Siemens SIMATIC S7 300 6AG1332-5HF00-2AB0 HMI Case
Siemens SIMATIC S7 300 6AG1332-5HF00-2AB0 HMI Case
6AG1332-5HF00-2AB0 Siemens SIMATIC S7-300 Module Housing Repair Replacement
S7-300 6AG13325HF002AB0 SM 332 analog output modules HMI Case systems are intended for stationary use in locations protected against the weather. The operating conditions surpass the requirements of DIN IEC 60721-3-3.
Class 3M3 (mechanical requirements)
Class 3K3 (climatic requirements)
Analog output module SM 332; AO 8 x 12 bit; 6AG1332-5HF00-2AB0 Plastic Shell Properties
• 8 outputs in one group
• The output can be selected by individual channel
– Voltage output
– Current output
• Resolution 12 bits
• Programmable diagnostics and diagnostic interrupt
• Programmable diagnostic interrupt
• Electrically isolated from the backplane bus interface and load voltage
• Supports parameter reassignment in RUN
VICPAS supply 6AG1332-5HF00-2AB0 Siemens S7 300 Simatic Module Plastic Case Cover Replacement Part. All of them with VICPAS 365 days warranty and support Urgent Worldwide Shipping.
Specifications:
The table below describes the parameters of the 6AG1332-5HF00-2AB0 Siemens SIMATIC SM 332 analog output modules Case Parts.
| Part Number : | 6AG1332-5HF00-2AB0 |
| Atmospheric pressure: | 1080 to 660 hPa |
| Temperature: | –40 °C to +70°C |
| Warranty: | 365 days Warranty |
| Product Line: | Siemens Simatic S7-300 |
| Dimensions W x H x D (mm): | 40 x 120.4 x 110.8 |
| Safety isolation: | SELV circuit |
| Power consumption: | 57 W |
| Power loss: | Typ. 9 W |
| Efficiency: | 84 % |
Related Siemens Simatic S7-300 Part No. :
| Siemens Simatic S7-300 | Description | Inventory status |
| 6AG1331-1KF02-7AB0 | Siemens SIPLUS S7-300 Plastic Case SM 331 Replacement | Available Now |
| 6AG1331-7KB02-2AB0 | SIMATIC S7 300 SM 331 Plastic Shell Repair Part | In Stock |
| 6AG1331-7KF02-2AB0 | Siemens S7-300 SM 331 Housing Enclosure Repair | Available Now |
| 6AG1331-7NF00-2AB0 | Siemens S7-300 SM 331 Plastic Shell Replacement | In Stock |
| 6AG1331-7NF10-2AB0 | Siemens S7-300 SM 331 Plastic Case Replacement | In Stock |
| 6AG1331-7PF01-4AB0 | SIMATIC S7 300 SM331 HMI Enclosure Replacement | In Stock |
| 6AG1331-7PF11-4AB0 | SIMATIC S7 300 Plastic Case SM 331 Replacement | Available Now |
| 6AG1332-5HB01-2AB0 | Siemens S7-300 SM 332 Housing Repair Replacement | Available Now |
| 6AG1332-5HD01-7AB0 | Siemens S7-300 Plastic Shell SM 332 Repair | In Stock |
| 6AG1332-5HF00-2AB0 | SIMATIC S7 300 HMI Case SM 332 Replacement | Available Now |
| 6AG1332-7ND02-4AB0 | Siemens S7-300 SM 332 Housing Replacement | In Stock |
| SIPLUS S7 300 PLC | Description | Inventory status |
Siemens SIMATIC S7-300 HMI Manuals PDF Download:
FAQ:
Question: Putting a New 6AG1332-5HF00-2AB0 Plastic Case Cover Body Module into Service
Answer: Proceed as follows to put the new module into service:
1. Open the front panel.
2. Reinstall the front connector.
3. Close the front panel.
4. Switch the load voltage back on.
5. Set the CPU to RUN mode again.
Question: When should I use expansion devices?
Answer: You can use EDs if the number of CU slots is insufficient for your application.
When using EDs, you might require further power supply modules in addition to the extra module racks and interface modules (IM). When using interface modules, you must ensure compatibility of the partner stations.
Common misspellings:
6AG1332-5HF00-2B0AG1332-5HF00-2AB0
6AG1332-5FH00-2AB0
6AG1332-5HF00-2A80
6AAG1332-5HF00-2AB0
- Loading...
- Tel
- *Title
- *Content
Fast Quote
Fast Quote
Worldwide Shipping
12 Months Warranty
Customize Service
- Tel
- *Title
- *Content
