Quick Service for Full HMI Parts Replacement
Home / All / IDEC / HG2A, HG2S, FT1A 3.8-inch PLC+HMI /

IDEC FT1A-M12RA-S Touch Screen Tablet Repair

IDEC FT1A-M12RA-S Touch Screen Tablet Repair

IDEC FT1A-M12RA-S Touch Screen Tablet Repair
CategoriesHG2A, HG2S, FT1A 3.8-inch PLC+HMI
BrandVICPAS
ModelFT1A-M12RA-S
Warranty365 Days
Shipping2-4 workdays
BrandIDEC
Supply PartsTouch Screen Glass
Display Size3.7 inches
FOB portGuangzhou, Shenzhen, Hongkong
Terms of PaymentWestern Union, MoneyGram, T/T, Paypal, PayPal, T/T ,Credit Card, Western Union
Update TimeNov 23,2024
Detail Information

IDEC FT1A 3.8IN PLC+HMI FT1A-M12RA-S Touch Screen Glass Replacement


IDEC FT1A 3.8IN PLC+HMI HMI Parts FT1A-M12RA-S Touch Digitizer Glass for repair replacement

Mounting

Place the FT1A-M12RA-S Touch Screen Glass in a panet cut-out and fasten with the attached mounting clips at four places uniformly. Do not tighten excessively, otherwise the FT1A may be defommed or damaged. When installing the FT1A-M12RA-S Touch Membrane vertically, make sure that the power input terminal is on the upper side. If the mounting clips are tightened obliquely to the panel, the IDEC FT1A may fall off the panel. Please attach this product to press down FT1A-M12RA-S Touch Digitizer Glass in the portion of the mountain of gasket. Once removing especially in the attaching again, be careful. There is a possibility that it may become impossible to maintain waterproof ability.


Notes for Operation

The screen becomes blank when the backlight is burnt out; however, the FT1A-M12RA-S Touchscreen remains enabled. Incorrect touch panel operation will occur when operating the touch panel when the backlight appears to be turned off but is actually burnt out. Please note that this erroneous operation may result in damage. At temperatures over the rated operating temperature, the clock accuracy is affected. Adjust the clock before use. For applications which require clock accuracy, adjust the clock periodically. When more than one button is pressed at the same time, due to the detection characteristics of FT1A-M12RA-S Touch Panel, only the gravity center of the pressed area is sensed and the unit assumes that only one button is pressed. Thus, when more than one button is pressed simultaneously, the resulting operation is not guaranteed.





Specifications:

The table below describes the parameters of the IDEC FT1A-M12RA-S Touch Membrane HMI.

Operating Humidity: 10 to 90% RH
Operating Temperature: -20 ~ 60°C
Product Line: FT1A 3.8IN PLC+HMI
Storage Temperature: -20 ~ 70°C
Brand: IDEC
Model Number: FT1A-M12RA-S
Display Size: 3.7"
Warranty: 1-Year Warranty
Screen Type: Analog Resistive Film
Corrosion Immunity: Free from corrosive gases


Related IDEC FT1A 3.8IN PLC+HMI No. :

FT1A 3.8IN PLC+HMI Description Inventory status
FT1A-C12RA-B IDEC FT1A 3.8IN PLC+HMI Touch Screen Panel Replacement In Stock
FT1A-C12RA-S IDEC FT1A 3.8IN PLC+HMI Touch Digitizer Glass Repair Available Now
FT1A-C14KA-B IDEC FT1A 3.8IN PLC+HMI Touch Screen Film Replacement In Stock
FT1A-C14KA-S IDEC FT1A 3.8IN PLC+HMI Touch Screen Glass Repair Available Now
FT1A-C14SA-B IDEC FT1A 3.8IN PLC+HMI Touch Screen Display Replacement In Stock
FT1A-C14SA-S IDEC FT1A 3.8IN PLC+HMI MMI Panel Screen Repair Available Now
FT1A-M12RA-B IDEC FT1A 3.8IN PLC+HMI Touchscreen Monitor Replacement In Stock
FT1A-M14KA-B IDEC FT1A 3.8IN PLC+HMI Touch Screen Film Replacement In Stock
FT1A-M14KA-S IDEC FT1A 3.8IN PLC+HMI HMI Touch Membrane Repair Available Now
FT1A-M14SA-B IDEC FT1A 3.8IN PLC+HMI Touch Screen Glass Replacement In Stock
FT1A-M14SA-S IDEC FT1A 3.8IN PLC+HMI Touch Screen Panel Repair Available Now
FT1A 3.8IN PLC+HMI Description Inventory status

IDEC FT1A 3.8IN PLC+HMI Manuals PDF Download:

  • IDEC-FT1A-SmartAXIS-Brochure
  • IDEC-FT1A-Touch-Datasheet

  • FAQ:

    Question: Can I connect external devices to the FT1A-M12RA-S Machine?

    Answer: Yes, the FT1A-M12RA-S HMIs typically offer various communication ports, such as Ethernet, USB, RS232, or RS485. These ports allow you to connect external devices, such as PLCs, sensors, or other control equipment, for data exchange and system integration.


    Question: How do I calibrate the touch screen on the FT1A-M12RA-S HMI?

    Answer: To calibrate the touch panel of FT1A-M12RA-S, go to the calibration settings in the HMI menu. Follow the on-screen instructions to touch specific calibration points accurately. This process ensures accurate touch input across the screen.

    Common misspellings: 

    FTA-M12RA-S

    FT1A-M12RAS

    FT1A-MM12RA-S

    FT1A-M12RA-SS

    FT1A-M12R-AS

    Review
    • Loading...
    Please send your message to us
    *Email
    Tel
    *Title
    *Content
    Upload
    • Only supports .rar/.zip/.jpg/.png/.gif/.doc/.xls/.pdf, maximum 20MB.
    Do you want to quickly know the product quotation you need?
    • Fast Quote
    • Worldwide Shipping
    • 12 Months Warranty
    • Customize Service
    subscription
    KEEP IN TOUCH
    Please send your message to us
    *Email
    Tel
    *Title
    *Content
    Upload
    • Only supports .rar/.zip/.jpg/.png/.gif/.doc/.xls/.pdf, maximum 20MB.
    CONTACT US
    QR code
    Mobile Web