Sigmatek ETV0811 Touch Panel Protective Film Repair Kit
SIGMATEK ETV0811 Touch Screen Panel Glass Protective Film Repair
The following clearance is required for the Sigmatek ETV0811 Protective Film Touch Digitizer Glass Terminal cover: Rear side, left and right 5 cm. Above and below 10 cm. A mounting position of 60° to 120° is also required. The ETV0811 Touchscreen Panel Front Overlay terminal must be connected to earth through the mounting on control cabinet or over the ETV0811 Touch screen panel glass Film terminal provided. It is important to create a low-ohm earth connection, only then can error-free operation be guaranteed. The earth connection should have the maximum cross section and the largest electrical surface possible.
VICPAS supply SIGMATEK Einbauterminal VARAN ETV0811 touchscreen panel with protective film overlay, all of them are brand new with 365 days VICPAS warranty. The ETV0811 Control Panel with EDGDE Technology combines control, operation and visualization in a single unit. Local as well as decentralized I/O systems can be connected over the VARAN bus and therefore not bound to a specific topology when constructing your system. The available interface connections can be programmed completely from the application.
Specifications:
The table below describes the parameters of the Sigmatek VARAN ETV0811 Front Overlay Touchscreen Panel.
| Part Number : | ETV0811 |
| Product Line: | Sigmatek VARAN |
| Screen diagonal | 8.4 in |
| Warranty: | 365 Days Warranty |
| Input Power | 24 VDC |
| Display Type: | TFT color |
| Mounting position: | Vertical |
| Input Type: | Touchscreen |
| Serial interface Type: | RS232 |
| Storage | -20 to 70°C |
Related Sigmatek Panel Part No. :
| Sigmatek VARAN | Description | Inventory status |
| ETV 0501 | Sigmatek Einbauterminal VARAN Touch Screen Protective Film Repair | In Stock |
| ETV 0551 | Einbauterminal VARAN Sigmatek Touch Panel Protective Film Replacement | Available Now |
| ETV 0551-V | Sigmatek Einbauterminal VARAN Touchscreen Protective Film Repair | In Stock |
| ETV 0552-B | Einbauterminal VARAN Sigmatek HMI Touch Screen Glass Protective Film | Available Now |
| ETV 0552-K | Sigmatek Einbauterminal VARAN Touch Screen Panel Front Overlay Repair | In Stock |
| ETV 0555 | Sigmatek Einbauterminal VARAN Front Overlay Touch Membrane | In Stock |
| ETV 0811 | Sigmatek Einbauterminal VARAN HMI Touch Glass Front Overlay Repair | In Stock |
| ETV 0851 | Sigmatek Einbauterminal VARAN Touch Digitizer Glass Overlay Repair | Available Now |
| ETV 0851-I | Sigmatek Einbauterminal VARAN HMI Panel Glass Protective Film | Available Now |
| ETV 0855 | Einbauterminal VARAN Touch Screen Monitor Front Overlay Replacement | In Stock |
| ETV 085A | Sigmatek Einbauterminal VARAN MMI Touch Screen Front Overlay | In Stock |
| ETVA-0501 | Sigmatek Einbauterminal VARAN HMI Touch Screen Protective Film | In Stock |
| SIGMATEK HMI | Description | Inventory status |
SIGMATEK ETV0811 Control Panel Manuals PDF Download:
FAQ:
Question:How to exchange the Sigmatek ETV0811 Battery?
Answer:
1. Disconnect the power to the ETV.
2. Open the locking screws on the back f the terminal with a PH-1 screwdriver:
3. Lift rear panel of the terminal:
For HW version 1.x:
4. Using the strap, remove the battery the holder (see arrow).
5. Insert the new battery with the correct polarity and close the terminal.
(+ Pole toward the backside)
From HW version 2.x:
4. Using the strap, remove the battery from the holder (see arrow).
5. Place the new battery in the holder with the correct polarity (+ Pole toward the frontside) and replace the cover.
Question:What is the price of SIGMATEK ETV0811 Front Overlay Touch Screen Monitor?
Answer: Submit a quote request, send us an email for our best price.
Common misspellings: ：
ET0811
ETV081
EVT0811
ET0V811
ETV0B11
ETVO811
ETV08811
EETV0811
- Loading...
- Tel
- *Title
- *Content
Fast Quote
Fast Quote
Worldwide Shipping
12 Months Warranty
Customize Service
- Tel
- *Title
- *Content
