Sigmatek ETT 1561 ETT 1962 Touch Panel Glass Repair
SIGMATEK ETT 1561 ETT 1962 Touch Screen Panel Glass Protective Film Repair
Order each part separately is available
The following clearance is required for the Sigmatek ETT 1561 ETT 1962 Protective Film Touch Digitizer Glass Terminal cover: Rear side, left and right 5 cm. Above and below 10 cm. A mounting position of 60° to 120° is also required. The ETT 1561 ETT 1962 Touchscreen Panel Front Overlay terminal must be connected to earth through the mounting on control cabinet or over the ETT 1561 ETT 1962 Touch screen panel glass Film terminal provided. It is important to create a low-ohm earth connection, only then can error-free operation be guaranteed. The earth connection should have the maximum cross section and the largest electrical surface possible.
VICPAS supply SIGMATEK Einbauterminal ETT 1561 ETT 1962 touchscreen panel with protective film overlay, all of them are brand new with 365 days VICPAS warranty. The ETT 1561 ETT 1962 Control Panel with EDGDE Technology combines control, operation and visualization in a single unit. Local as well as decentralized I/O systems can be connected over the bus and therefore not bound to a specific topology when constructing your system. The available interface connections can be programmed completely from the application.
Specifications:
The table below describes the parameters of the Sigmatek ETT 1561 ETT 1962 Front Overlay Touchscreen Panel.
| Part Number : | ETT1561 / ETT1962 |
| Product Line: | Sigmatek ETT |
| Screen diagonal | 15 / 19 in |
| Warranty: | 365 Days Warranty |
| Input Power | 24 VDC |
| Display Type: | TFT color |
| Mounting position: | Vertical |
| Input Type: | Touchscreen |
| Serial interface Type: | RS232 |
| Storage | -20 to 70°C |
Related Sigmatek Panel Part No. :
| Einbauterminal | Description | Inventory status |
| ETT 311 | Sigmatek Einbauterminal Touch Screen Repair | In Stock |
| ETT 321 | Einbauterminal Sigmatek Touch Panel Replacement | Available Now |
| ETT 312 | Sigmatek Einbauterminal Touchscreen Repair | In Stock |
| ETT 352 | Einbauterminal Sigmatek HMI Touch Screen Glass | Available Now |
| ETT 353 | Sigmatek Einbauterminal Touch Screen Panel Repair | In Stock |
| ETT 412 | Sigmatek Einbauterminal Touch Membrane Repair | In Stock |
| ETT 731 | SIGMATEK Einbauterminal HMI Touch Glass Repair | In Stock |
| ETT 771 | Sigmatek Einbauterminal Touch Digitizer Glass Repair | Available Now |
| ETT 1561 | Sigmatek Einbauterminal HMI Panel Glass Replacement | Available Now |
| ETT 1962 | Einbauterminal SIGMATEK Touch Screen Monitor Repair | In Stock |
| SIGMATEK HMI | Description | Inventory status |
SIGMATEK Control Panel Manuals PDF Download:
FAQ:
Question:How to exchange the Sigmatek ETT 1561 ETT 1962 Battery?
Answer:
1. Disconnect the power to the ETT.
2. Open the locking screws on the back f the terminal with a PH-1 screwdriver:
3. Lift rear panel of the terminal:
For HW version 1.x:
4. Using the strap, remove the battery the holder (see arrow).
5. Insert the new battery with the correct polarity and close the terminal.
(+ Pole toward the backside)
From HW version 2.x:
4. Using the strap, remove the battery from the holder (see arrow).
5. Place the new battery in the holder with the correct polarity (+ Pole toward the frontside) and replace the cover.
Question:What is the price of SIGMATEK ETT 1561 ETT 1962 Front Overlay Touch Screen Monitor?
Answer: Submit a quote request, send us an email for our best price.
Common misspellings: ：
ETT561
ETT151
ET1T561
TET1962
ETTl962
ETT19962
- Loading...
- Tel
- *Title
- *Content
Fast Quote
Fast Quote
Worldwide Shipping
12 Months Warranty
Customize Service
- Tel
- *Title
- *Content
