Schneider Magelis MPCYT50NAN00N Touch Screen Monitor
Schneider Magelis MPCYT50NAN00N Touch Screen Monitor
Schneider Magelis MPCYT50NAN00N Touch Digitizer Glass Protective Film Replacement
Magelis Schneider MPCYT50NAN00N industrial touchscreen display is in the range of Magelis iDisplay, the component type is Flat Screen. MPCYT50NAN00N Touch Screen Panel Glass Terminal Type is Touchscreen display integrating USB or RS232C port, VGA or DVI-D port. MPCYT50NAN00N Touch Digitizer Glass HMI rated supply voltage is 100...240 V AC power supply conforming to EN 61131-2, Supply voltage limits 98...264 V. Schneider Magelis iDisplay MPCYT50NAN00N Touchscreen Panel is 15 inch with active matrix colour TFT 1024 X 768 pixels XGA LCD Display .
VICPAS supply MPCYT50NAN00N Magelis Schneider Terminal Front Overlay Touch screen glass with 365 Days warranty and support Urgent Worldwide Shipping. Extra care should be taken with respect to the specification concerning vibration levels when installing or moving the MPCYT50NAN00N Touchscreen digiziter glass front overlay terminal. If the MPCYT50NAN00N Protective Film HMI Panel Glass Magelis terminal is moved, for example, while it is installed in a rack equipped with caster wheels, the unit can receive excessive shock and vibration.
Specifications:
The table below describes the parameters of the MPCYT50NAN00N Magelis Schneider Front Overlay Touch Screen Panel.
Part Number: | MPCYT50NAN00N |
Display Type: | LCD TFT |
Screen Diagonal: | 15 in |
Warranty: | 365 Days |
Product Line: | Magelis iDisplay Series |
Terminal Type: | Touchscreen Display |
Operating Temp.: | 0...50 °C |
Storage Temp.: | -20...60 °C |
Display Resolution: | 1024 x 768 pixels XGA |
Operating System: | Windows XPe SP2 |
Schneider Magelis iDisplay HMI Manuals PDF Download:
FAQ:
Question: How to install the Schneider Magelis iDisplay MPCYT50NAN00N Unit?
Answer:
1. Place the unit face down on a dry, soft surface and attach the gasket to the rear side, in the installation groove (see picture below):2. Check that the gasket is correctly attached to the unit. The upper surface of the gasket should protrude evenly approximately 2 mm (0.08 in.) out of the groove.
Note: When installing the iDisplay unit's installation gasket, avoid contact with the sharp edges of the iDisplay frame, and press the gasket completely into its groove.
3. Insert each installation fastener securely into the slot’s recess at the top and bottom of the unit:
4. Attach and Secure the Rear Installation Attachments:
5. Insert each of the fasteners. Pull the fastener back until it is flush with the rear of the attachment hole.
Note: The corresponding installation attachments can be purchased as spare parts with the maintenance kit ref.: MPC YK 50 MNT KIT.
6. Use a screw driver to tighten to 0.5 N•m (4.5 lb-in) each of the fastener screws and secure the iDisplay in place:
7. iDisplay Viewing Angle.
Ensure that the panel’s viewing angle is tilted no more than 30 degrees from parallel to the operator (i.e. operator is directly in front).
Question: When an alarm appears on Magelis Schneider MPCYT50NAN00N Protective Film Touch Panel Glass Terminal, what does it means?
Answer:
• The alarm relay is closed (if this function is selected).
• The alarm strip is updated.
Common misspellings:
MPCYT50AN00NPCYT50NAN00N
MPCYT50NAN0N0
MPCYT5ONAN00N
MPCYYT50NAN00N
- Loading...
- Tel
- *Title
- *Content
- Fast Quote
- Worldwide Shipping
- 12 Months Warranty
- Customize Service
- Tel
- *Title
- *Content